Other instruments, appliances and machines.

BLEED AND OVERHEAT MONITORING SYSTEM. FOR…

BLEED AND OVERHEAT MONITORING SYSTEM. FOR USE IN AIRCRAFT. THE MAIN FUNCTION OF WHICH IS TO PREVENT DAMAGE FROM TOO MUCH HEAT AND PRESSURE, PREVENTS ICE BUILD UP (ON WINGS), MONITORS THE SYSTEM TO CREW OR MAINTENANCE PERSONNEL.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING: GENERAL INTERPRETATIVE RULES (GIRS): GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031: MEASURING OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTORS.

GIR 3C HAS BEEN USED AS IT IS CONSIDERED THERE IS NO ESSENTIAL CHARACTER AND THEREFORE HAS BEEN CLASSIFIED TO LAST IN NUMERICAL ORDER WITHIN THE TARIFF GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 903180 OTHER INSTRUMENTS, APPLIANCES AND MACHINES.

CN CODE 90318038 ELECTRONIC; OTHER THAN FOR MEASURING OR CHECKING GEOMETRICAL QUANTITIES. TARIC CODE 9031803890 OTHER THAN FOR USE IN CIVIL AIRCRAFT OR ACCELERATION MEASUREMENT DEVICES FOR AUTOMOTIVE APPLICATIONS, COMPRISING ONE OR MORE ACTIVE AND/OR PASSIVE ELEMENTS AND ONE OR MORE SENSORS, THE WHOLE CONTAINED IN A HOUSING.

ALSO CLASSIFIED IN ACCORDANCE WITH THE HSENS OF HEADING 9031.

BTI Reference:
GB503334685.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: TRANSPORT EQUIPMENT AIRCRAFT PARTS ELECTRONIC SCIENTIFIC AND MEASURING EQUIPMENT

A ROTARY POSITION SENSOR, USED AS A POTENTIOMETER.…

A ROTARY POSITION SENSOR, USED AS A POTENTIOMETER. THE SENSOR HAS AN OPERATIONAL SPEED OF 120 RPM.

THE MAXIMUM SUPPLY VOLTAGE ACROSS THE ELEMENT IS APPROXIMATELY 42 VDC. THE SENSOR IS USED ON MACHINERY WHERE ROTARY POSITION NEEDS TRANSLATING TO AN ELECTRICAL OUTPUT.

TYPICAL APPLICATIONS ARE: THROTTLE POSITION SENSING AND GEARBOX GEAR SELECTION ON CARS. MAXIMUM CURRENT DRAW THROUGH THE WIPER IS LESS THAN 1 MICRO AMP, VOLTAGE IS APPLIED ACROSS THE ELEMENT; THE OUTPUT IS FED IN TO A HIGH IMPEDENCE METER AND AS THE SHAFT IS ROTATED THE CHANGING RESISTANCE GIVES AN OUTPUT VOLTAGE PROPORTIONAL TO THE SHAFT POSITION.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031 - MEASURING OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTORS GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 9031 80 - OTHER INSTRUMENTS, APPLIANCES AND MACHINES CN CODE 90318091 OTHER THAN ELECTRONIC: FOR MEASURING OR CHECKING GEOMETRICAL QUANTITIES TARIC 90318091 90 - OTHER THAN FOR USE IN CIVIL AIRCRAFT ALSO CLASSIFIED IN ACCORDANCE WITH:- HARMONIZED SYSTEM EXPLANATORY NOTES (HSEN) TO HEADING 9031 COMBINED NOMENCLATURE EXPLANATORY NOTES (CNEN) TO 9031 80 91

BTI Reference:
GB503246288.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: SENSORS PRECISION EQUIPMENT ROTARY FOR MEASURING GEOMETR. QUANTITIES

Fibre optic gyroscope is opto-electronic…

Fibre optic gyroscope is opto-electronic sensor for measuring angular rate based on the sagnac effect.

Each fibre optic gyroscope consists of the following main components: fibre optic winding on a bobbin, light source in the form of a super luminescent diode, optic couplers, optical polarizer, piezoceramic modulator photo-diode and processing electronics.

The gyroscope is normally packed individually and is not for use in civil aircrafts.

Classification justification: Classification is determined by the interpretation of GIRs 1 and 6 to the Combined Nomenclature and by the wording of CN codes: 9031, 9031 80, 9031 80 38 and 9031 80 38 90

BTI Reference:
MT0017-16.
Start date of validity:
.
End date of validity:
2016-12-31.

Fibre optic gyroscope is opto-electronic…

Fibre optic gyroscope is opto-electronic sensor for meusuring angular rate based on the sagnac effect.

Each fibre optic gyroscope consists of the following main components: fibre optic winding on a bobbin, light source in the form of a super luminescent diode, optic couplers, optical polarizer, piezoceramic modulator photo-diode and processing electronics.

The gyroscope is normally packed individually and are for use in civil aircrafts.

Classification justification: Classification is determined by the interpretation of GIRs 1 and 6 to the Combined Nomenclature and by the wording of CN codes: 9031, 9031 80, 9031 80 38 and 9031 80 38 05

BTI Reference:
MT0013-16.
Start date of validity:
.
End date of validity:
2016-12-31.

A FULL FEATURED INSURANCE TELEMATICS DEVICE.…

A FULL FEATURED INSURANCE TELEMATICS DEVICE. SUPPORTS REQUIREMENTS FOR ACCURATE DRIVER BEHAVIOUR DATA GATHERING, FIRST NOTIFICATION OF INCIDENT LOGGING AND IS READY FOR INTEGRATION INTO TELEMATICS SERVICE PROVIDER SERVER SYSTEMS.

WINDSCREEN MOUNTED INTO VEHICLES WTH A ANTI-TAMPER ALERT. THE DEVICE CONTAINS A GPS RECEIVER, INTERNAL GOS ANTENNA, MOTION DETECTION, QUAD BAND AND INTERNAL U-BLOX CHIPSET.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031 MEASURING OR CHECKING INSTRFUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER GIR 3C HAS BEEN USED AS IT IS CONSIDERED THERE IS NO ESSENTIAL CHARACTER AND THEREFORE HAS BEEN CLASSIFIED TO LAST IN NUMERICAL ORDER WITHIN THE TARIFF GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 903180 OTHER INSTRUMENTS, APPLIANCES AND MACHINES: CN CODE 90318038 OTHER THAN FOR MEASURING OR CHECKING GEOMETRICAL QUANTITIES TARIC CODE 9031803810 ACCELERATION MEASUREMENT DEVICE FOR AUTOMOTIVE APPLICATIONS, COMPRISING ONE OR MORE ACTIVE AND/OR PASSIVE ELEMENTS AND ONE OR MORE SENSOR, THE WHOLE CONTAINED IN A HOUSING ALSO CLASSIFIED IN ACCORDANCE WITH ADDITIONAL NOTE 1 CHAPTER 90 THE SCOPE OF HS EXPLANATORY NOTE 9031

BTI Reference:
GB503275181.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: ELECTRONIC SCIENTIFIC AND MEASURING EQUIPMENT FOR MOTOR VEHICLES DATA COMMUNICATION EQUIPMENT

ANGLE MEASUREMENT SENSOR USING CONDUCTIVE…

ANGLE MEASUREMENT SENSOR USING CONDUCTIVE FLUID TO MEASURE THE RESISTANCE DEPENDENT ON THE TILT, WITH ONBOARD LED ALIGNMENT AID, CONVERSION CIRCUIT BOARD AND CONNECTION FOR REMOTE LCD READOUT.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031 FOR MEASURING OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTORS GIR 3B HAS BEEN USED AS THE MOTION CAPTURE DEVICE IS CONSIDERED TO GIVE THE ITEM IS ESSENTIAL CHARACTER.

GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 9031 80 FOR OTHER INSTRUMENTS, APPLIANCES AND MACHINES CN CODE 90318038 - ELECTRONIC; OTHER THAN FOR MEASURING OR CHECKING GEOMETRICAL QUANTITIES TARIC CODE 9031803890 - OTHER THAN ELSEWHERE SPECIFIED IN THIS SUBHEADING

BTI Reference:
GB503245193.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: PRECISION EQUIPMENT ELECTRONICS ENCODERS ROTARY FOR MEASURING GEOMETR. QUANTITIES

A POSITION TRANSDUCER. CONSISTS OF A SPRING…

A POSITION TRANSDUCER. CONSISTS OF A SPRING LOADED WIRE DRUM INTERNALLY CONNECTED TO A POTENTIOMETER.

AS THE CABLE IS EXTENDED THROUGH THE GEARS OF THE POTENTIOMETER IT GIVES A RESISTIVE OUTPUT PROPORTIONAL TO THE LENGTH OF CABLE EXTENDED.

THE OUTPUT SIGNAL IS VOLTAGE DIVIDER. THE TRANSDUCER MEAURES LENGTH, WHICH IS A GEOMETRICAL QUANTITY.

IT ALSO MEASURES ACCELERATION AND VELOCITY. IT IS FOR HIGH ACCELERATION TEST APPLICATIONS IN POTENTIALLY WET ENVIRONMENTS.

HAS DIFFERENT FULL STROKE RANGES. HAS A HIGH TENSION HEAVY DUTY MEASURING CABLE DESIGNED FOR THE DEMANDS OF FLIGHT AND AUTOMOTIVE CRASH TESTS.

COMES WITH A MOUNTING BRACKET FOR INSTALLATION IN HARD TO FIT AREAS. HAS AN ALUMINUM ENCLOSURE.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031 - MEASURING MACHINES OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTIONS.

GIR 2A HAS BEEN USED AS THE GOODS ARE UNASSEMBLED GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 903180 - OTHER INSTRUMENTS, APPLIANCES AND MACHINES, ELECTRONIC CN CODE 90318034 OTHER TARIC CODE 9031803490 - OTHER

BTI Reference:
GB123651885.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: ELECTRONIC SCIENTIFIC AND MEASURING EQUIPMENT

A POSITION TRANSDUCER. CONSISTS OF A SPRING…

A POSITION TRANSDUCER. CONSISTS OF A SPRING LOADED WIRE DRUM INTERNALLY CONNECTED TO A POTENTIOMETER.

AS THE CABLE IS EXTENDED THROUGH THE GEARS OF THE POTENTIOMETER IT GIVES A RESISTIVE OUTPUT PROPORTIONAL TO THE LENGTH OF CABLE EXTENDED.

THE OUTPUT SIGNAL IS VOLTAGE DIVIDER. THE TRANSDUCER MEAURES LENGTH, WHICH IS A GEOMETRICAL QUANTITY.

LINEAR POSITION TO 25 INCHES, FITS IN TIGHT SPACES. HAS HANDY MOUNTING BRACKET AND A POLYCARBONATE ENCLOSURE.

BTI Reference:
GB123651787.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: ELECTRONIC SCIENTIFIC AND MEASURING EQUIPMENT

SENSOR AND DIAGNOSTIC ASSEMBLY FOR AIR BAGS…

SENSOR AND DIAGNOSTIC ASSEMBLY FOR AIR BAGS USED IN AUTMOTIVE VEHICLES. FORMS PART OF AN AUTMOTIVE AIRBAG SHOCK SENSOR AND IS MADE OF METAL.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING: 9031 MEASURING OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTORS.

GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL: 903180 ELECTRONIC. CN CODE: 90318038 OTHER THAN FOR USE IN CIVIL AIRCRAFT.

TARIC CODE: 9031803810 ACCELERATION MEASUREMENT DEVICE FOR AUTOMOTIVE APPLICATIONS, COMPRISING ONE OR MORE ACTIVE AND/OR PASSIVE ELEMENTS AND ONE OR MORE SENSORS, THE WHOLE CONTAINED IN A HOUSING.

ALSO CLASSIFIED IN ACCORDANCE WITH: GENERAL CHAPTER NOTE 2(B) GENERAL CHAPTER NOTE 5. HSEN 9031 REFERS

BTI Reference:
GB501639961.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: SCIENTIFIC AND MEASURING EQUIPMENT

THIS TORQUE SENSOR IS DESIGNED FOR BOTH STATIC…

THIS TORQUE SENSOR IS DESIGNED FOR BOTH STATIC AND DYNAMIC MEASUREMENTS ON NON-ROTATING APPLICATIONS.

SHEAR STRAINS IN THE TORSION SHAFT ARE MEASURED BY MEANS OF METAL FOIL STRAIN GAUGES CONNECTED ON THE SENSOR ELEMENT.

APPLYING A SUPPLY VOLTAGE GENERATES AN ELECTRICAL OUTPUT SIGNAL THAT IS DIRECTLY PROPORTIONAL TO THE APPLIED MECHANICAL TORQUE.

MEASUREMENT RANGES FROM 0 - 0.005 NM TO 0 - 5000 NM.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 9031 - MEASURING OR CHECKING INSTRUMENTS, APPLIANCES AND MACHINES, NOT SPECIFIED OR INCLUDED ELSEWHERE IN THIS CHAPTER; PROFILE PROJECTORS GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 9031 80 - OTHER INSTRUMENTS, APLLIANCES AND MACHINES CN CODE 903180 38 ELECTRONIC; OTHER THAN FOR MEASURING OR CHECKING GEOMETRICAL QUANTITIES TARIC 90318038 90 - OTHER THAN ELSEWHERE SPECIFIED IN THIS COMMODITY CODE

BTI Reference:
GB503245095.
Start date of validity:
.
End date of validity:
2016-12-31.

National keywords: OF METAL ELECTRONIC SCIENTIFIC AND MEASURING EQUIPMENT SENSORS