Other / Of pumps / Pumps for liquids, whether or not fitted with a measuring device; liquid elevators.

CONNECTION WATER BYPASS. A STEEL CONNECTION…

CONNECTION WATER BYPASS. A STEEL CONNECTION FOR WATER BYPASS USED IN A VEHICLE'S COOLING SYSTEM.

THE CONNECTOR IS ATTACHED TO THE COOLANT PUMP IN THE VEHICLE'S COOLING SYSTEM. DESIGNED TO A SPECIFIC SIZE AND SURFACE FINISH AND PREPARED TO WORK SOLELY WITH THE PUMP.

NOT FOR GENERAL USE. THE FUNCTION OF THE CONNECTOR IS TO INLET THE COOLER FROM THE PUMP INTO THE ENGINE COOLING SYSTEM WHEN THE ENGINE TEMPERATURE IS TOO HIGH.

THE WATER PUMP USES CENTRIFUGAL FORCE TO SEND FLUID TO THE OUTSIDE OF THE PUMP WHILE IT SPINS, CAUSING FLUID TO BE DRAWN FROM THE CENTRE CONTINUOUSLY.

THE INLET IS LOCATED NEAR THE CENTRE OF THE PUMP SO THAT FLUID RETURNING FROM THE RADIATOR HITS THE PUMP VANES.

THE PUMP VANES FLING THE FLUID TO THE OUTSIDE OF THE PUMP WHERE IT CAN ENTER THE ENGINE. THE FLUID LEAVING THE PUMP FLOWS FIRST THROUGH THE ENGINE BLOCK AND CYLINDER HEAD, THEN INTO THE RADIATOR AND FINALLY BACK TO THE PUMP.

THE CONNECTOR IS MADE FROM WELDED LOW-CARBON STEEL TUBING SUITABLE FOR BENDING, FLARING , BEADING, FORMING AND BRAZING, AND COVERED WITH ZINC PLATE.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 8413: PUMPS FOR LIQUIDS, WHETHER OR NOT FITTED WITH A MEASURING DEVICE; LIQUID ELEVATORS.

GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 841391: PARTS; OF PUMPS. TARIC CODE: 8413910090: OTHER THAN ELSEWHERE SPECIFIED IN THIS SUBHEADING.

ALSO CLASSIFIED IN ACCORDANCE WITH: NOTE 2 (B) TO SECTION XVI REFERS. HSEN TO 841391 REFERS.

BTI Reference:
GB123943084.
Start date of validity:
.
End date of validity:
2020-06-26.

National keywords: OF STEEL

ADAPTER ASSEMBLY WATER BYPASS. A STEEL CONNECTION…

ADAPTER ASSEMBLY WATER BYPASS. A STEEL CONNECTION FOR WATER BYPASS USED IN A VEHICLE'S COOLING SYSTEM.

IT IS ATTACHED TO A COOLANT PUMP IN THE VEHICLE'S COOLING SYSTEM. MADE TO A SPECIFIC SIZE AND SURFACE FINISH, THE CONNECTOR HAS BEEN PREPARED TO WORK SOLELY WITH THE COOLANT PUMP.

NOT FOR GENERAL USE. THE FUNCTION OF THIS CONNECTOR IS TO INLET THE COOLER FROM THE PUMP INTO THE ENGINE COOLING SYSTEM WHEN THE ENGINE IS TOO HIGH.

THE WATER PUMP USES CENTRIFUGAL FORCE TO SEND FLUID TO THE OUTSIDE PUMP WHILE IT SPINS, CAUSING FLUID TO BE DRAWN FROM THE CENTRE CONTINUOUSLY.

HTE INLET IS LOCATED NEAR THE CENTRE OF THE PUMP SO THAT FLUID RETURNING FROM THE RADIATOR HITS THE PUMP VANES.

THE PUMP VANES FLING THE FLUID TO THE OUTSIDE OF THE PUMP, WHERE IT CAN ENTER THE ENGINE. THE FLUID LEAVING THE PUMP FLOWS FIRST THROUGH THE ENGINE AND CYLINDER HEAD, THEN INTO THE RADIATOR AND FINALLY BACK TO THE PUMP.

THE CONNECTION WATER BYPASS IS MADE OF A COMBINATION OF COLD-DRAWN BUTTWELD CARBON STEEL MECHANICAL TUBING AND ALUMINIUM ALLOY.

BTI Reference:
GB123944375.
Start date of validity:
.
End date of validity:
2020-06-26.

National keywords: OF STEEL

A PRINTED CIRCUIT BOARD ASSEMBLY SPECIFICALLY…

A PRINTED CIRCUIT BOARD ASSEMBLY SPECIFICALLY DESIGNED AND MANUFACTURED SOLELY FOR USE IN A FUEL PUMP OF THE KIND FOUND ON GARAGE FORECOURTS TO DISPENSE PETROL.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR 1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 8413 FOR PUMPS FOR LIQUIDS, WHETHER OR NOT FITTED WITH A MEASURING DEVICE; LIQUID ELEVATORS GIR 6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL 8413 91 FOR PARTS OF PUMPS TARIC 84139100 90 FOR OTHER THAN ELSEWHERE SPECIFIED IN THIS SUBHEADING ALSO CLASSIFIED IN ACCORDANCE WITH:- NOTE 2 (B) TO SECTION XVI

BTI Reference:
GB501793460.
Start date of validity:
.
End date of validity:
2020-03-27.

National keywords: ELECTRONIC ASSEMBLIES

CONNECTION KIT USED IN A FUEL PUMP. CONSISTS…

CONNECTION KIT USED IN A FUEL PUMP. CONSISTS OF FOUR SCREWS, FOUR WASHERS AND A CONNECTION PLATE WHICH HOUSES A NUT AND BOLT.

BTI Reference:
GB123336502.
Start date of validity:
.
End date of validity:
2019-10-23.

PUMP FLANGE USED IN A FUEL PUMP.

PUMP FLANGE USED IN A FUEL PUMP.

BTI Reference:
GB123336404.
Start date of validity:
.
End date of validity:
2019-10-23.

A MECHANICAL SEAL FACE MADE OF TUNGSTEN CARBIDE.…

A MECHANICAL SEAL FACE MADE OF TUNGSTEN CARBIDE. THE SEAL FACE IS IN THE FORM OF A RING WITH AN OUTER DIAMETER OF APPROXIMATELY 6 CM. IT ATTACHES TO THE HOUSING OF A LIQUID PUMP AND FORMS PART OF A MECHANICAL SEAL ASSEMBLY THAT PREVENTS LIQUID FROM ESCAPING.

BTI Reference:
GB122403328.
Start date of validity:
.
End date of validity:
2018-12-02.

National keywords: TUNGSTEN RINGS, FORMS

DECKPLATE. THIS IS A BILGE PUMP COVER FOR…

DECKPLATE. THIS IS A BILGE PUMP COVER FOR A CENTRIFUGAL SUBMERSIBLE PUMP. THE PRODUCT IS MANUFACTURED FROM UV STABILISED PLASTIC. INCLUDES A SNAP SHUT LID TO REMAIN CLOSED WHEN PUMP IS NOT IN USE.

Classification justification: CLASSIFICATION HAS BEEN DETERMINED IN ACCORDANCE WITH THE FOLLOWING:- GENERAL INTERPRETATIVE RULES (GIR)S GIR1 HAS BEEN USED TO CLASSIFY THIS PRODUCT BY THE TERMS OF HEADING 8413: PUMPS FOR LIQUIDS, WHETHER OR NOT FITTED WITH A MEASURING DEVICE; LIQUID ELEVATORS GIR6 HAS BEEN USED TO CLASSIFY THE GOODS TO SUBHEADING LEVEL. 841391: PARTS; OF PUMPS.

TARIC CODE 8413910090: OTHER THAN ELSEWHERE SPECIFIED WITHIN THIS HEADING. ALSO CLASSIFIED IN ACCORDANCE WITH:- NOTE 2(B) TO SECTION XVI HSEN NOTE (C) TO HEADING 8413

BTI Reference:
GB501051420.
BTI Reference:
GB501051224.
BTI Reference:
GB501051126.
BTI Reference:
GB501051322.
Start date of validity:
.
End date of validity:
2017-11-06.

National keywords: OF PLASTIC COVERS LIDS PUMPS